News

Sign up today to get the latest news and updates from EPC on new product announcements, applications work, and much more. Sign up for EPC email updates or text "EPC" to 22828.

EPC Introduces Two eGaN ICs Combining Gate Drivers with High Frequency GaN FETs for Improved Efficiency, Reduced Size and Lower Cost

EPC Introduces Two eGaN ICs Combining Gate Drivers with High Frequency GaN FETs for Improved Efficiency, Reduced Size and Lower Cost

EPC2112 and EPC2115 GaN-based monolithic integrated solutions offer power systems designers the ability to increase efficiency in an extremely small size.

EL SEGUNDO, Calif. — March 2018 — Efficient Power Conversion Corporation (EPC) announces the EPC2112 and EPC2115 enhancement-mode monolithic GaN power transistor with integrated driver products. The EPC2112 is a 200 V, 40-mΩ eGaN® FET plus integrated gate driver. In comparison, the EPC2115 is an integrated circuit with dual 150 V, 70-mΩ eGaN FETs plus gate drivers. Both products are capable of operating up to 7 MHz and are available in low inductance, extremely small, 2.9 mm x 1.1 mm BGA surface-mount passivated die.

Read more
Categories: Press Releases

GaN Power Modules Deliver Over 1400 W/in3 for 48 V – 12 V DC-DC and Up to 10 MHz for Point-of-Load Power Conversion

GaN Power Modules Deliver Over 1400 W/in3 for 48 V – 12 V DC-DC and Up to 10 MHz for Point-of-Load Power Conversion

Efficient Power Conversion’s EPC9204 and EPC9205 power modules demonstrate the efficiency enhancements and significant size reduction achieved in DC-DC power conversion using high frequency switching eGaN® power transistors and integrated circuits.

EL SEGUNDO, Calif.— March 2018 — Efficient Power Conversion Corporation (EPC) introduces two new GaN power modules for DC-DC conversion, increasing efficiency across the 48 V to point-of-load power architecture. The EPC9205 is a high-power density PCB-based power module for 48 V – 12 V conversions while the EPC9204 address the 20 V – point-of-load conversion with an ultra-thin profile PCB-based power module.

Read more
Categories: Press Releases

GaN-Based 48 V to 12 V Regulated Power Supply Development Board Delivers over 1250 W per Cubic Inch and Over 96% Efficiency

GaN-Based 48 V to 12 V Regulated Power Supply Development Board Delivers over 1250 W per Cubic Inch and Over 96% Efficiency

Efficient Power Conversion’s EPC9130 five-phase development board demonstrates the extreme size reduction and efficiency enhancement for power conversion achieved using high frequency switching eGaN® power transistors.

EL SEGUNDO, Calif.— March 2018 —Efficient Power Conversion Corporation (EPC) introduces EPC9130 48 V − 12 V non-isolated, fully regulated development board.  This five-phase board with 12 A per phase has a maximum output current of 60 amps, making the board capable of over 700 W. The EPC9130 provides extremely high-power density exceeding 1250 W per cubic inch, and over 96% efficiency.

Read more
Categories: Press Releases

EPC to Showcase Industry-Leading Performance in High Power Density DC-DC Conversion and Multiple High Frequency Applications Using eGaN Technology at APEC 2018

EPC to Showcase Industry-Leading Performance in High Power Density DC-DC Conversion and Multiple High Frequency Applications Using eGaN Technology at APEC 2018

EPC will exhibit live demonstrations showing how GaN technology’s superior performance is transforming power delivery for entire industries including computing, communications, and automotive.

EL SEGUNDO, Calif. — February 2018 — The EPC team will be delivering seven technical presentations on gallium nitride (GaN) technology and applications at APEC 2018 in San Antonio, Texas from March 4th through the 8th. In addition, the company will demonstrate its latest eGaN FETs and ICs in customers’ end products that are enabled by eGaN technology.

Read more
Categories: Press Releases

EPC Introduces 40 V Gallium Nitride Power Transistor 8 Times Smaller Than Equivalently Rated MOSFETS

EPC Introduces 40 V Gallium Nitride Power Transistor 8 Times Smaller Than Equivalently Rated MOSFETS

EPC2049 GaN power transistor offers power systems designers a 40 V, 5 mΩ power transistor about 8 times smaller than equivalently rated silicon MOSFETs for point of load converters, LiDAR, and low inductance motor drive.

EL SEGUNDO, Calif. — December 2017 — EPC announces the EPC2049 power transistor for use in applications including point of load converters, LiDAR, envelope tracking power supplies, class-D audio, and low inductance motor drives. The EPC2049 has a voltage rating of 40 V and maximum RDS(on) of 5 mΩ with a 175 A pulsed output current.

Read more
Categories: Press Releases

EPC to Show GaN-Enabled Large Area Wireless Power and High Resolution LiDAR at 2018 CES

EPC to Show GaN-Enabled Large Area Wireless Power and High Resolution LiDAR at 2018 CES

Within the AirFuelTM Alliance booth at CES 2018, EPC will show how gallium nitride (GaN) semiconductors are at the core of large surface area wireless power. In the EPC hospitality suite, wirelessly powered systems for the home and GaN based, industry-leading LiDAR systems used in autonomous vehicles will be on display.

EL SEGUNDO, Calif. — December 2017 — Efficient Power Conversion (EPC) will be demonstrating the power of eGaN® technology to enhance two game-changing consumer applications – wireless power and LiDAR for self-driving cars – at the 2018 Consumer Electronics Show (CES) in Las Vegas, January 9th through the 12th.

Read more
Categories: Press Releases

150-Ampere LiDAR Development Board Can Deliver 5 Nano Second Pulses Using eGaN Technology From EPC

150-Ampere LiDAR Development Board Can Deliver 5 Nano Second Pulses Using eGaN Technology From EPC

Ultra-fast transition eGaN FETs used on the EPC9126HC can drive high current pulses up to 150 A and pulse widths as low as 5 ns, thus enhancing the quality of information a LiDAR system will detect, including the accuracy, precision, and processing speed.

EL SEGUNDO, Calif. — November 2017 — Efficient Power Conversion Corporation (EPC) announces the availability of the EPC9126HCa 100 V, 150 A high current pulsed laser diode driver evaluation board. In a LiDAR system, used to create 3-D maps for autonomous vehicle applications, speed and accuracy of object detection is critical. As demonstrated by this board, the rapid transition capability of eGaN FETs provide power pulses to drive the laser up to ten times faster than an equivalent MOSFET, thus enhancing the overall performance of a LiDAR system.

Read more
Categories: Press Releases

Efficient Power Conversion Corporation’s (EPC) eGaN Transistor Wins 2017 Impact Award from Electronics Component News Magazine

Efficient Power Conversion Corporation’s (EPC) eGaN Transistor Wins 2017 Impact Award from Electronics Component News Magazine

EPC2040, an eGaN® power transistor optimized for LiDAR applications, placed first in the Passive Components & Discrete Semiconductors category of ECN magazine’s prestigious 2017 Impact Award.

EL SEGUNDO, Calif — November  2017 Efficient Power Conversion Corporation’s (EPC) is proud to announce that Electronic Component News (ECN) — a leading trade publication for electronic design engineers — has awarded the EPC2040, enhancement mode gallium nitride (eGaN) transistor its ECN Impact Award for 2017 in the Passive Components and Discrete Semiconductors category.

Read more
Categories: Press Releases

EPC Announces Development Board Operating Up To 10 MHz for High Efficiency at High Frequency Point-of-Load DC-DC Conversion

EPC Announces Development Board Operating Up To 10 MHz for High Efficiency at High Frequency Point-of-Load DC-DC Conversion

The EPC9086 high efficiency half-bridge development board can operate up to 10 MHz featuring a 30 V EPC2111 eGaN® half bridge in combination with the recently introduced high speed Peregrine Semiconductor PE29102 gate driver.

EL SEGUNDO, Calif.—October 2017 — Efficient Power Conversion Corporation (EPC) today announces the availability of The EPC9086 development board, a high efficiency half-bridge development board that can operate up to 10 MHz.  The EPC9086 board measures 2” x 2” and contains a 30 V, 15 A EPC2111 enhancement-mode gallium nitride half bridge in combination with the recently introduced PE29102 gate driver from Peregrine Semiconductor.

Read more
Categories: Press Releases

Efficient Power Conversion (EPC) Announces MIGVAN as Sales, Marketing, and Technical Support Partner for Israel

Efficient Power Conversion (EPC) Announces MIGVAN as Sales, Marketing, and Technical Support Partner for Israel

MIGVAN now represents EPC’s Israel sales, marketing, and technical support to assist customers in adopting eGaN® FETs and ICs for leading-edge power conversion systems using gallium nitride

EL SEGUNDO, Calif.— October 2017 — To support its accelerating growth throughout Israel, Efficient Power Conversion Corporation (EPC) is proud to announce the appointment of MIGVAN as its sales, marketing, and technical support representative.  MIGVAN Technologies & Engineering Ltd, founded in 1988, is devoted to promoting and selling advanced technology electronic components and subsystems to the Israeli electronics industry.

Read more
Categories: Press Releases

EPC Announces a Full Range of Wireless Power Demonstration Kits That Can Be Used to Design Systems That Power Anything from Lamps to Laptops

EPC Announces a Full Range of Wireless Power Demonstration Kits That Can Be Used to Design Systems That Power Anything from Lamps to Laptops

Superior characteristics of eGaN® FETs and ICs, such as low output capacitance, low input capacitance, low parasitic inductances, and small size used in these demonstration kits show that GaN FETs and ICs are ideal for increasing efficiency in highly resonant, AirFuel™ Alliance compatible wireless power transfer systems.

EL SEGUNDO, Calif.—October 2017 — Efficient Power Conversion Corporation (EPC) today announces the availability of two new demonstration kits -- the EPC9127, a complete wireless power kit including a 10 W, class 2 amplifier, category 3 receiver device and the EPC9128, consisting of a 16 W, class 3 amplifier and two receiver devices (categories 3 and 4). These systems, coupled with previously announced EPC9120, 33 W class 4 and the EPC9121 multi-mode kit capable of operating to either an AirFuel Class 2 standard with a category 3 device or a Qi (A6)/PMA standard with a compatible receiving device provide a full range of wireless power demonstration kits to allow for complete, wide-spread implementation.

Read more
Categories: Press Releases

Efficient Power Conversion (EPC) to Present GaN-based Large Surface Area Wireless Power Solution at the 2017 Wireless Power Summit

Efficient Power Conversion (EPC) to Present GaN-based Large Surface Area Wireless Power Solution at the 2017 Wireless Power Summit

EPC will exhibit an innovative wireless power tabletop at 2017 Wireless Power Summit highlighting the capability of GaN-based semiconductor magnetic resonance technology to provide wireless power over a large surface area to many receiving devices such as cell phones, laptop computers, and table lamps – at the same time!

EL SEGUNDO, Calif. — September 2017 — The future of wireless power and its eventual ubiquitous adoption is dependent upon the ability of end users to place any electrical item on a surface and have it powered without having to “plug in.” It is this ability that EPC will demonstrate at the Wireless Power Summit 2017 being held in Denver, Colorado October 5th and 6th at the Embassy Suites Hotel Downtown.

Read more
Categories: Press Releases

Efficient Power Conversion Corporation (EPC) Receives 2017 Top 10 Power Products Award from Electronic Products China Magazine/21iC Media

Efficient Power Conversion Corporation (EPC) Receives 2017 Top 10 Power Products Award from Electronic Products China Magazine/21iC Media

EPC’s latest family of eGaN® transistors and ICs takes a quantum leap in increasing Performance while reducing costs for new and existing applications currently served by MOSFETs 

EL SEGUNDO, Calif — September 2017 Efficient Power Conversion Corporation’s Gen 5 eGaN® transistor and IC family has been honored with an Electronic Products China / 21iC Media’s “Top 10 Power Products – Best Application Award.” The award presentation was announced on September 15th, 2017 in Beijing, China during 21iC Power Conference 2017.

Read more
Categories: Press Releases

Efficient Power Conversion (EPC) Introduces 60 W Class-E Amplifier Development Board with Latest Generation 200 V eGaN FET Enabling High Efficiency Up to 15 MHz

Efficient Power Conversion (EPC) Introduces 60 W Class-E Amplifier Development Board with Latest Generation 200 V eGaN FET Enabling High Efficiency Up to 15 MHz

EPC’s new EPC9083 development board enables power system designers to easily and quickly evaluate the high efficiency achieved with a high performance 200 V gallium nitride transistor in a class-E amplifier used in wireless power, LiDAR, current-mode class-D, and push-pull converters operating up to 15 MHz.

EL SEGUNDO, Calif.— August 2017 — Providing an easy-to-use way for power systems designers to evaluate the exceptional performance of gallium nitride transistors and get their products into volume production quickly, Efficient Power Conversion Corporation (EPC) announces the EPC9083, a high efficiency, flexible, GaN-based differential mode development board that can operate up to 15 MHz, including 6.78 MHz which is popular for wireless power applications.

Read more
Categories: Press Releases

Charge Cell Phones to Laptops Simultaneously – EPC Introduces Complete Class 4 AirFuel Alliance Compatible Wireless Power Demonstration Kit Capable of Transmitting up to 33 W

Charge Cell Phones to Laptops Simultaneously – EPC Introduces Complete Class 4 AirFuel Alliance Compatible Wireless Power Demonstration Kit Capable of Transmitting up to 33 W

Superior characteristics of eGaN® FETs, such as low output capacitance, low input capacitance, low parasitic inductances, and small size make them ideal for increasing efficiency in highly resonant, AirFuel wireless power transfer systems.

EL SEGUNDO, Calif.—August 2017 — Efficient Power Conversion Corporation (EPC) today announces the availability of a complete class 4 wireless power charging kit, the EPC9120. The system can transmit up to 33 W while operating at 6.78 MHz (the lowest ISM band).  The purpose of this demonstration kit is to simplify the evaluation process of using eGaN FETs for highly efficient wireless power transfer.  The EPC9120 utilizes the high frequency switching capability of EPC gallium nitride transistors to facilitate wireless power systems with full power efficiency between 80% and 90% under various operating conditions.

Read more
Categories: Press Releases

EPC Joining PCIM Asia 2017 For Knowledge Exchange with Engineers on How to Choose among 6.78 MHz Amplifier Topologies for High Power, Highly-resonant Wireless Charging Applications

EPC Joining PCIM Asia 2017 For Knowledge Exchange with Engineers on How to Choose among 6.78 MHz Amplifier Topologies for High Power, Highly-resonant Wireless Charging Applications

EL SEGUNDO, Calif. — June 21st, 2017 -- Efficient Power Conversion Corporation, the world’s leader in enhancement-mode gallium nitride on silicon (eGaN®) power FETs and ICs, enables a lower-cost, single transmit amplifier solution that can wirelessly charge devices, regardless of the standard used in the receiving device.

Meet EPC experts on power management at PCIM Asia Exhibition and Conference on June 28th, 2017 at 11 a.m. at Meeting Room 2, B2 of Shanghai World Expo Exhibition and Convention Center in China. Dr. Michael de Rooij, Vice President of Application Engineering, EPC, will share with engineers about a choice among topologies to achieve customer-oriented designs for high power, highly resonant wireless charging applications.

Read more
Categories: Press Releases

Wolfram Krueger Joins Efficient Power Conversion (EPC) as Vice President of European Sales

Wolfram Krueger Joins Efficient Power Conversion (EPC) as Vice President of European Sales

Mr. Krueger to direct EPC’s European sales organization and assist customers in adopting eGaN® FETs and Integrated Circuits for leading-edge power conversion systems

EL SEGUNDO, Calif. — June 2017 — To support its accelerating growth, Efficient Power Conversion Corporation (EPC) is proud to announce that Wolfram Krueger has joined the EPC leadership team as Vice President of European sales. Mr. Krueger has over 30 years of sales operation experience within the semiconductor industry. His primary responsibilities at EPC are creating and implementing sales and marketing strategies to achieve the company’s sales objectives throughout Europe. He is based in Cologne, Germany.

Read more
Categories: Press Releases

Rompower Announces The AC/DC Laptop Power Adaptor Technology Capable of 94% Efficiency, 20 W/in3 Power Density in an Incredibly Small Package

Rompower Announces The AC/DC Laptop Power Adaptor Technology Capable of 94% Efficiency, 20 W/in3 Power Density in an Incredibly Small Package

Taking advantage of the high performance of eGaN® FETs, Rompower Energy Systems has announced a reference design for a tiny, 65 W, 94% efficient AC/DC power adaptor for laptops and other mobile devices.

TUCSON, Az. – June 2017 – Rompower Energy Systems, an internationally recognized research and development company in the field of power conversion, announces the availability of technology for an extremely small, highly efficient AC/DC power adapter. In the quest for higher power density, the efficiency of the adapter is critical in order to decrease the heat dissipation. The reference design is measuring just 3.19 cubic inches in size, this adapter provides 65 W of power at greater than 94% efficiency over the entire input voltage range (90 Vac – 264 Vac).  The adapter has a power density of 20 W/in3. This high efficiency means that the device runs cooler than standard AC/DC adapters.

Read more
Categories: Press Releases

Efficient Power Conversion (EPC) Introduces High Frequency Monolithic Gallium Nitride Half Bridge Enabling 12 V to 1.8 V System Efficiency Over 85% at 5 MHz at 14 A Output

Efficient Power Conversion (EPC) Introduces High Frequency Monolithic Gallium Nitride Half Bridge Enabling 12 V to 1.8 V System Efficiency Over 85% at 5 MHz at 14 A Output

EPC2111 GaN half bridge offers power systems designers a solution that increases efficiency for complete overall point-of-load system applications over 85% at 14 A when switching at 5 MHz and over 80% when switching at 10 MHz and converting from 12 V to 1.8 V.

EL SEGUNDO, Calif. — June2017 — EPC announces the EPC2111, 30 V enhancement-mode monolithic GaN transistor half bridge. By integrating two eGaN® power FETs into a single device, interconnect inductances and the interstitial space needed on the PCB are eliminated.  This increases both efficiency (especially at higher frequencies) and power density, while reducing assembly costs to the end user’s power conversion system. The EPC2111 is ideal for high frequency 12 V to point-of-load DC-DC conversion.

Read more
Categories: Press Releases

Efficient Power Conversion (EPC) Introduces 200 V Gallium Nitride Power Transistor 12 Times Smaller Than Equivalently Rated MOSFETS

Efficient Power Conversion (EPC) Introduces 200 V Gallium Nitride Power Transistor 12 Times Smaller Than Equivalently Rated MOSFETS

EPC2046 GaN power transistor offers power systems designers a 200 V, 25 mΩ power transistor about 12 times smaller than equivalently rated silicon MOSFETs for wireless power, multi-level AC-DC power supplies, robotics, and solar micro inverters.

EL SEGUNDO, Calif. — May 2017 — EPC announces the EPC2046 power transistor for use in applications including wireless power, multi-level AC-DC power supplies, robotics, solar micro inverters, and low inductance motor drives. The EPC2046 has a voltage rating of 200 V and maximum RDS(on) of 25 mΩ with a 55 A pulsed output current.

Read more
Categories: Press Releases
RSS
12345678910 Last