EL SEGUNDO, Calif. — December 2020 — BrightLoop Converters has greatly reduced the size, cost and improved reliability of its latest BB SP DC-DC buck converters thanks to Efficient Power Conversion Corporation’s (EPC) EPC2029 enhancement-mode gallium nitride (eGaN^®) FET transistors. By switching from silicon (Si) transistors to gallium nitride (GaN), BrightLoop was able to increase the switching frequency of their design from 200 kHz to 600 kHz, while keeping the same efficiency. This design change increased the power density of the solution by a factor of approximately two and this resulted in lower cost by enabling the implementation of a smaller enclosure.

EPC’s EPC2029 is an 80 V, 48 A eGaN^® FET featuring a 1 mm ball pitch. The wider pitch allows for placement of additional and larger vias under the device to enable high current carrying capability despite the extremely small 2.6 mm x 4.6 mm footprint.

The EPC2152 ePower™ Stage enables higher performance and smaller solution size for high power density, low-cost DC-DC conversion demonstrated in the EPC9151 power module.

EL SEGUNDO, Calif.— December, 2020 — EPC announces the availability of the EPC9151, a 300 W bidirectional DC-DC voltage regulator in the in the very small 16^th brick format which is just 33 mm x 22.9 mm (1.3 x 0.9 in). The EPC9151 power module features Microchip’s dsPIC33CK digital signal controller (DSC) with the EPC2152 ePower™ Stage integrated circuit from EPC to achieve greater than 95% efficiency in a 300 W 48 V to/from 12 V converter design.  Additional phases can be added to this scalable 2-phase design to further increase power.

The combination of Microchip Technology’s digital signal controllers with ultra-efficient eGaN^® FETs from EPC (Efficient Power Conversion) enable best-in-class power density of 730 W/in³ for high efficiency, low cost DC-DC Conversion.

EL SEGUNDO, Calif.— July, 2020 — EPC announces the availability of the EPC9143, a 300 W DC-DC voltage regulator in 16^th brick size. The EPC9143 power module integrates Microchip’s dsPIC33CK digital signal controller (DSC) with the latest generation EPC2053 eGaN FETs from EPC to achieve 96% efficiency in a 48 V input to 12 V output conversion at 25 A.  The switching frequency of 500 kHz enables the 300 W in the very small 16^th brick format which is just 33 mm x 22.9 mm (1.3 x 0.9 in). Additional phases can be added to this scalable 2-phase design to further increase power. The flexibility of the Microchip digital controllers allows the input voltage to be adjusted from 8 V – 72 V and the output voltage from 3.3 V – 25 V.

Efficient Power Conversion (EPC) will showcase the company’s latest ePower™ Stage IC family of products showing how GaN technology’s superior performance is transforming power delivery for computing, communications, robotics, and transportation at the PCIM Europe 2020 Digital Days.

EL SEGUNDO, Calif.— June 2020 — The EPC team will be delivering three technical presentations and participating in two panel discussions on gallium nitride (GaN) technology and applications at the upcoming PCIM Europe 2020 Digital Days, July 7 – 8. In addition, the company will participate in the event’s virtual exhibit, showing its latest eGaN FETs and ICs in customers’ end products that are rapidly adopting eGaN technology.

Over the past decade computers, displays, smart phones and other consumer electronics systems have become thinner while also becoming more powerful. As a result, the market continues to increase its demand for thinner power supply solutions with greater power density. This article examines the feasibility of adopting various non-isolated dc-dc stepdown topologies for an ultra-thin 48-V to 20-V, 250-W power solution.

How2Power
May, 2020
Read article

Three years ago, the cost of making medium voltage eGaN FETs fell below the cost of equivalently rated power MOSFETs. At that time EPC decided to use the performance and cost advantages of eGaN FETs to aggressively pursue applications with input, or output, voltage around 48 V. Specifically, automotive and computer applications is where 48 V conversion is becoming the new architecture, the new standard for power systems.

Power Systems Design
March 31, 2020
Read article

Efficient Power Conversion (EPC) introduces the first of a new integrated circuit (IC) product family offering higher performance and smaller solution size for high power density applications including DC-DC conversion, motor drive, and Class-D audio.

EL SEGUNDO, Calif.— March 2020 — EPC announces the introduction of an 80 V, 12.5 A power stage integrated circuit designed for 48 V DC-DC conversion used in high-density computing applications and in motor drives for e-mobility.

Alex Lidow is the CEO of Efficient Power Conversion, probably the most prominent advocate for gallium nitride, delivering the first GaN transistor in 2009. After a decade of selling products, DESIGN&ELEKTRONIK editor Ralf Higgelke met him to discuss some of the latest advances in that area.

DESIGN&ELEKTRONIK
February 20, 2020
Read article

With silicon near its theoretical limits new designs heavily favor the continued adoption of GaN devices. GaN devices are early in their evolution, with advances in performance and integration and more products coming.

Electronics Weekly
December, 2019
Read article

It’s getting harder to avoid using GaN power transistors and ICs, says Alex Lidow. There are many reasons to use GaN-on-Si power transistors such as eGaN FETs, in telecoms, vehicles, healthcare and computing. Smaller, faster, lower cost, and more integrated, GaN-on-Si devices have spent a decade gaining the confidence and trust of designers across the spectrum of power conversion applications.

Electronic Specifier
November 20, 2019
Read article

Ahead of December’s Power Conference in Munich, Bodo Arlt took the opportunity to get an insight into Alex Lidow’s thoughts on where the GaN market is now and where he sees the potential applications for the future. Dr. Lidow is the CEO and Co-founder of Efficient Power Conversion (EPC).

Bodo’s Power Systems
November, 2019
Read article

In support of a widening customer base in Europe, Efficient Power Conversion Corporation has expanded its technical leadership team to assist customers in the adoption of eGaN^® FETs and Integrated circuits for applications including DC-DC, Lidar, motor control, and beyond.

EL SEGUNDO, Calif. — October, 2019 — To support its accelerating design activity, and to provide local technical support to EPC’s customers in Europe, Efficient Power Conversion Corporation (EPC) is proud to announce that Marco Palma, a seasoned expert, has joined the EPC technical leadership team as Senior FAE Manager for Europe. 

It is expected that there will be more than 175 zettabytes of data by 2025. Data center construction and deployment, as well as upgrading efforts in existing older ones, is booming with the advent of 5G, starting in earnest at the 2020 Olympics in Japan (6G is already being discussed for future development) and the growth of artificial intelligence (AI) and machine learning (ML).

It makes so much sense to me that GaN should be the power transistor of choice in Data Center power architectures where size, efficiency and speed are critical. In all the topologies with 48 VIN, the highest efficiency was achieved with GaN devices.

EDN
June 2019
Read article

Today’s GaN FETs are improving rapidly in size and performance. The benchmark devices are still 300 times away from their theoretical performance limits. The early GaN adopters needed the speed. Big examples were lidar systems for autonomous cars, drones, and robots, and 4G/LTE base stations. The volume has grown, and now GaN power devices are at a point where the prices are equivalent to the slower, bigger and aging power MOSFET. Thus, it is time for GaN’s frontal assault!

Bodo’s Power Systems
June 2019
Read article

Efficient Power Conversion (EPC) will provide their industry-leading gallium nitride-based power devices in wafer form for ease of power systems integration.

EL SEGUNDO, Calif.— June 2019 — EPC announces the availability of their industry-leading enhancement-mode gallium nitride (GaN) devices in wafer form for ease of integration.  EPC’s eGaN^® FETs and ICs are traditionally sold as singulated chip-scale devices with solder bars or solder bumps. 

eGaN FETs and ICs enable very high-density power converter design, owing to their compact size, ultra-fast switching, and low on-resistance. The limiting factor for output power in most high-density converters is junction temperature, which prompts the need for more effective thermal design. The chip-scale packaging of eGaN FETs and ICs offer six-sided cooling, with effective heat extraction from the bottom, top, and sides of the die. This article presents a high-performance thermal solution to extend the output current capability of eGaN-based converters.

EDN
Read article

EPC's chief executive, Alex Lidow, believes his GaN devices now beat silicon on performance and price, reports Rebecca Pool.

For EPC chief executive, Alex Lidow, this year's PCIM Europe 2019 has been all about applications. Presenting myriad enhanced-mode GaN FETs and ICs in end-products, the company is making a big play for 48 V DC-DC power conversion in advanced computing and automotives.

Compound Semiconductor
Read article

This year’s PCIM Europe was attended by a record number of visitors, over 12,000. Over half (54%) were from outside Germany. They came to see over 500 exhibitors and while the subject matter was diverse and wide-ranging, there were some themes that emerged. GaN and SiC jostled for attention at this year’s PCIM Europe. Showing the potential that GaN has already realised, Efficient Power Conversion (EPC) had a stand that was well-stocked with examples of the eGaN FET technology that the company introduced in 2009.

Electronic Specifier
Read article

Efficient Power Conversion (EPC) expands AEC Q101 product family with the addition of the EPC2214, 80 V gallium nitride transistor optimized for high resolution lidar systems.

EL SEGUNDO, Calif.— April 2019 — EPC announces successful AEC Q101 qualification of the 80 V EPC2214 designed for lidar systems in the automotive industry and other harsh environments. 

Efficient Power Conversion (EPC) has recently introduced two new, 100V, GaN devices that are able to handle 48V server and automotive needs. I will be examining the 48V server power solutions to the processor as well as in automotive and energy storage systems (See my article Bi-directional DC/DC power supplies: Which way do we go?) bi-directional supplies, in an EDN exclusive article coming up in the near future. GaN power transistors MUST be a part of these kinds of architectures; from my point-of-view there is no better alternative.

Planet Analog
Read article