EPC and Analog Devices introduce reference design using a new Analog controller fully optimized to drive EPC GaN FETs. The combination of the new Analog LTC7890 synchronous GaN buck controller with ultra-efficient eGaN^® FETs from EPC (Efficient Power Conversion) enables up to 2 MHz switching frequency for high power density and low-cost DC-DC Conversion.

EL SEGUNDO, Calif.—  March, 2022 — EPC announces the availability of the EPC9160, a dual output synchronous buck converter reference design board operating at 2 MHz switching frequency that converts an input voltage of 9 V to 24 V to a 3.3 V or 5 V output voltage and delivers up to 15 A continuous current for both outputs. Thanks to the high switching frequency the converter size is very small, only 23 mm x 22 mm for both outputs, and the inductor height is only 3 mm.

Efficient Power Conversion’s EPC9204 and EPC9205 power modules demonstrate the efficiency enhancements and significant size reduction achieved in DC-DC power conversion using high frequency switching eGaN^® power transistors and integrated circuits.

EL SEGUNDO, Calif.— March 2018 — Efficient Power Conversion Corporation (EPC) introduces two new GaN power modules for DC-DC conversion, increasing efficiency across the 48 V to point-of-load power architecture. The EPC9205 is a high-power density PCB-based power module for 48 V – 12 V conversions while the EPC9204 address the 20 V – point-of-load conversion with an ultra-thin profile PCB-based power module.

Efficient Power Conversion’s EPC9130 five-phase development board demonstrates the extreme size reduction and efficiency enhancement for power conversion achieved using high frequency switching eGaN^® power transistors.

EL SEGUNDO, Calif.— March 2018 —Efficient Power Conversion Corporation (EPC) introduces EPC9130 48 V − 12 V non-isolated, fully regulated development board.  This five-phase board with 12 A per phase has a maximum output current of 60 amps, making the board capable of over 700 W. The EPC9130 provides extremely high-power density exceeding 1250 W per cubic inch, and over 96% efficiency.

Ultra-fast transition eGaN FETs used on the EPC9126HC can drive high current pulses up to 150 A and pulse widths as low as 5 ns, thus enhancing the quality of information a LiDAR system will detect, including the accuracy, precision, and processing speed.

EL SEGUNDO, Calif. — November 2017 — Efficient Power Conversion Corporation (EPC) announces the availability of the EPC9126HCa 100 V, 150 A high current pulsed laser diode driver evaluation board. In a LiDAR system, used to create 3-D maps for autonomous vehicle applications, speed and accuracy of object detection is critical. As demonstrated by this board, the rapid transition capability of eGaN FETs provide power pulses to drive the laser up to ten times faster than an equivalent MOSFET, thus enhancing the overall performance of a LiDAR system.

The EPC9086 high efficiency half-bridge development board can operate up to 10 MHz featuring a 30 V EPC2111 eGaN^® half bridge in combination with the recently introduced high speed Peregrine Semiconductor PE29102 gate driver.

EL SEGUNDO, Calif.—October 2017 — Efficient Power Conversion Corporation (EPC) today announces the availability of The EPC9086 development board, a high efficiency half-bridge development board that can operate up to 10 MHz.  The EPC9086 board measures 2” x 2” and contains a 30 V, 15 A EPC2111 enhancement-mode gallium nitride half bridge in combination with the recently introduced PE29102 gate driver from Peregrine Semiconductor.

Superior characteristics of eGaN^® FETs and ICs, such as low output capacitance, low input capacitance, low parasitic inductances, and small size used in these demonstration kits show that GaN FETs and ICs are ideal for increasing efficiency in highly resonant, AirFuel™ Alliance compatible wireless power transfer systems.

EL SEGUNDO, Calif.—October 2017 — Efficient Power Conversion Corporation (EPC) today announces the availability of two new demonstration kits -- the EPC9127, a complete wireless power kit including a 10 W, class 2 amplifier, category 3 receiver device and the EPC9128, consisting of a 16 W, class 3 amplifier and two receiver devices (categories 3 and 4). These systems, coupled with previously announced EPC9120, 33 W class 4 and the EPC9121 multi-mode kit capable of operating to either an AirFuel Class 2 standard with a category 3 device or a Qi (A6)/PMA standard with a compatible receiving device provide a full range of wireless power demonstration kits to allow for complete, wide-spread implementation.

EPC’s new EPC9083 development board enables power system designers to easily and quickly evaluate the high efficiency achieved with a high performance 200 V gallium nitride transistor in a class-E amplifier used in wireless power, LiDAR, current-mode class-D, and push-pull converters operating up to 15 MHz.

EL SEGUNDO, Calif.— August 2017 — Providing an easy-to-use way for power systems designers to evaluate the exceptional performance of gallium nitride transistors and get their products into volume production quickly, Efficient Power Conversion Corporation (EPC) announces the EPC9083, a high efficiency, flexible, GaN-based differential mode development board that can operate up to 15 MHz, including 6.78 MHz which is popular for wireless power applications.

EPC2046 GaN power transistor offers power systems designers a 200 V, 25 mΩ power transistor about 12 times smaller than equivalently rated silicon MOSFETs for wireless power, multi-level AC-DC power supplies, robotics, and solar micro inverters.

EL SEGUNDO, Calif. — May 2017 — EPC announces the EPC2046 power transistor for use in applications including wireless power, multi-level AC-DC power supplies, robotics, solar micro inverters, and low inductance motor drives. The EPC2046 has a voltage rating of 200 V and maximum R_DS(on) of 25 mΩ with a 55 A pulsed output current.

EPC’s new development boards can be configured as either a buck converter or a ZVS class-D amplifier, demonstrating reduced losses at high frequency using an eGaN FET synchronous bootstrap augmented gate drive.

EL SEGUNDO, Calif.— March 2016 — Efficient Power Conversion Corporation (EPC) Introduces the EPC9066, EPC9067, and EPC9068 development boards, which are configurable to a buck converter or as a ZVS class-D amplifier. These boards provide an easy-to-use way for power systems designers to evaluate the exceptional performance of gallium nitride transistors, enabling the designers to get their products into volume production quickly. All three boards feature a zero reverse recovery (Q_RR) synchronous bootstrap rectifier augmented gate driver to increase efficiency at high frequency operation, up to 15 MHz. The boards can produce a maximum output of 2.7 A in the buck and ZVS class-D amplifier configurations. Loss reduction is realized across the entire current range.

EPC9065 development board has the highest power and highest efficiency at 6.78 MHz for the AirFuel^TM wireless power standard, using eGaN^® FETs

EL SEGUNDO, Calif.— February 2016 — Efficient Power Conversion (EPC) announces the EPC9065, a development board that can serve as the amplifier stage for AirFuel^TM Alliance Class 4 and Class 5 wireless power transfer applications. This board is a Zero Voltage Switching (ZVS) differential-mode class-D amplifier development board configured at, but is not limited to, 6.78 MHz (Lowest ISM band).

EPC9059 development board showcases industry’s first monolithic half-bridge enhancement-mode gallium nitride (eGaN^®) integrated circuits for high current, high frequency point-of-load applications for increased power density.

EL SEGUNDO, Calif.— January 2016 — Efficient Power Conversion Corporation (EPC) introduces the EPC9059 half-bridge development board for high current, high frequency point-of-load (POL) applications using eGaN ICs to reduce power conversion size. The EPC9059 development board has a 30 V maximum device voltage with a 50 A maximum output current. In this application two 30 V EPC2100 eGaN IC’s operating in parallel with a single onboard gate driver to achieve higher output currents. GaN devices have superior current sharing capability compared to silicon MOSFETs, making them more attractive for parallel operation.

EPC’s new development boards enable power systems designers to easily and quickly evaluate the high efficiency achieved with 200 V gallium nitride transistors in class-E amplifiers, current-mode class-D, and push-pull converters operating up to 30 MHz.

EL SEGUNDO, Calif.— January 2016 — Providing an easy-to-use way for power systems designers to evaluate the exceptional performance of gallium nitride transistors and get their products into volume production quickly, Efficient Power Conversion Corporation (EPC) announces high efficiency, GaN-based differential mode development boards that can operate up to 30 MHz.

100 volt, 1 amp, 550 milliohm EPC2037 enhancement-mode gallium nitride power transistor is driven directly from a digital drive and delivers high frequency switching for exceptional performance in wireless charging Class-D and Class-E amplifier applications.

EL SEGUNDO, Calif. – October 2015 – Efficient Power Conversion Corporation (www.epc-co.com) introduces the EPC2037 as the newest member of EPC’s family of enhancement-mode gallium nitride power transistors (eGaN^® FETs).

EPC2106 GaN power transistor offers power systems designers a solution that switches over 2 MHz resulting in no interference with the AM band, reducing costs for filtering, thus making it ideal for low distortion Class-D audio.

EL SEGUNDO, Calif. — August 2015 — EPC announces the EPC2106, an enhancement-mode monolithic GaN transistor half bridge. By integrating two eGaN^® power FETs into a single device, interconnect inductances and the interstitial space needed on the PCB are eliminated. This increases both efficiency (especially at higher frequencies) and power density, while reducing assembly costs to the end user’s power conversion system.

New EPC2107 and EPC2108 eGaN^® power integrated circuits include monolithic half bridge and integrated bootstrap functions for A4WP compliant Class 2 and Class 3 solutions. In addition, development boards and complete wireless power solutions – transmit and receive devices – for quick and easy evaluations of these components are available.

EL SEGUNDO, Calif. — July 2015 — EPC announces the EPC2107 (100 V) and EPC2108 (60 V) eGaN half bridge power integrated circuits with integrated bootstrap FET, eliminating gate driver induced reverse recovery loses as well as the need for a high side clamp. This is the first time that a bootstrap FET has been integrated in an eGaN power circuit.

New family of eGaN power transistors offer superior performance, smaller size, and high reliability…at the price of a MOSFET.

EL SEGUNDO, Calif.— April 2015 — Efficient Power Conversion Corporation (EPC) announces the 60 V EPC2035 and 100 V EPC2036 eGaN power transistors designed to compete in price, while outperforming silicon. Price, the last barrier to widespread adoption of GaN transistors as silicon MOSFET replacements, has fallen. These products demonstrate that gallium nitride can displace silicon semiconductors and drive the industry back onto the Moore’s Law growth curve.

EPC9106 Class-D audio amplifier reference design, using high frequency switching gallium nitride power transistors, demonstrates efficiency enhancement, size reduction and eliminates need for a heat sink while delivering prosumer quality sound.

EL SEGUNDO, Calif. — February 2015 — Efficient Power Conversion Corporation (EPC) introduces the EPC9106, a reference design for a 150 W, 8 ohm Class-D audio amplifier.

The EPC2101 GaN power monolithic half bridge offers power systems designers a solution that increases efficiency and power density. For a complete buck converter, system efficiency approaches 87% at 14 A, and over 82% at 30 A when switching at 500 kHz and converting from 28 V to 1 V while reducing the board area occupied by transistors by 50% when compared to a discrete solution.

EL SEGUNDO, Calif. — November 2014 — EPC announces the EPC2101, 60 V enhancement-mode monolithic GaN transistor half bridge. By integrating two eGaN^® power FETs into a single device, interconnect inductances and the interstitial space needed on the PCB are eliminated, resulting in a 50% reduction in board area occupied by the transistors. This increases both efficiency (especially at higher frequencies) and power density, while reducing assembly costs to the end user’s power conversion system. The EPC2101 is ideal for high frequency DC-DC conversion.

EPC2105 GaN half bridge offers power systems designers a solution that increases efficiency and power density for complete buck converter systems approaching 98% at 10 A when switching at 300 kHz and converting from 48 V to 12 V, and 84% at 14 A when switching at 300 kHz and converting from 48 V to 1.0 V.

EL SEGUNDO, Calif. — November 2014 — EPC announces the EPC2105, 80 V enhancement-mode monolithic GaN transistor half bridge. By integrating two eGaN^® power FETs into a single device, interconnect inductances and the interstitial space needed on the PCB are eliminated. This increases both efficiency (especially at higher frequencies) and power density, while reducing assembly costs to the end user’s power conversion system. The EPC2105 is ideal for high frequency DC-DC conversion and enables efficient single stage conversion from 48 V directly to 1 V system loads.

EPC2025 GaN power transistor offers power systems designers a 300 V power transistor capable of 2ns rise times for high frequency DC-DC converters and medical diagnostic instruments.

EL SEGUNDO, Calif. — September 2014 — EPC announces the EPC2025, a 300 V power transistor for use in applications requiring high frequency switching in order to achieve higher efficiency and power density. Applications enhanced by higher switching speeds include ultra-high frequency DC-DC converters, medical diagnostic equipment, power inverters, and LED lighting.