In last month’s Safety & Compliance column in How2Power, “WBG Semiconductors Pose Safety And EMI Challenges In Motor Drive Applications,”[1]Kevin Parmenter made some assertions about the difficulties of using SiC, and to a lesser extent GaN, power semiconductors in large motor-drive applications. This commentary is a response to that article, showing that GaN can be a game changer in low-voltage integrated motors.

How2Power
February, 2021
Read article

Gallium nitride (GaN) devices offer performance in a small form factor, increasing the efficiency, and reducing the system cost for 48 V power conversion applications. They have been adopted in high volumes in high density computing, as well as many new automotive power system designs.

Electronic Specifier
February, 2021
Read article

The combination of the Renesas dual synchronous GaN buck controller and ultra-efficient eGaN^® FETs from EPC (Efficient Power Conversion) enables high power density and efficiency with the same BOM size and cost as silicon.

EL SEGUNDO, Calif.—  February, 2021 — EPC announces the availability of the EPC9157, a 300 W DC-DC demo board in the tiny 1/16^th brick size, measuring just 33 mm x 22.9 mm x 9mm (1.3 x 0.9 x 0.35 in). The EPC9157 demo board integrates the Renesas ISL81806 80 V dual synchronous buck controller with the latest-generation EPC2218 eGaN FETs from EPC to achieve greater than 95% efficiency for 48 V input to 12 V regulated output conversion at 25 A.  

In this episode, Alex Lidow and Marti McCurdy discusses EPC’s test-to-failure method in improving gallium nitride (GaN) devices. According to Alex, testing to failure has allowed EPC to tease out the exact stressors that cause failure and improve EPC’s GaN devices 10-100 times the reliability of commercial devices, and even 100 times reliability in space applications.

Alex and Marti discuss:

(1:30) Why test to fail
(4:14) Learning from failure data and stressors
(11:38) Safe Operating Area
(14:30) Mechanical stressors
(17:45) EPC Space

Listen now

Efficient Power Conversion (EPC) publishes Phase-12 Reliability Report adding to the extensive knowledge found in their first eleven reports. With this report, EPC demonstrates field experience of 226 billion eGaN ^® device hours and a robustness capability unmatched by silicon power devices.

EL SEGUNDO, Calif.— January 2021 — EPC announces its Phase-12 Reliability Report, documenting the strategy used to achieve a remarkable field reliability record. eGaN devices have been in volume production for more than eleven years and have demonstrated very high reliability in over 226 billion hours of operation, most of which are in vehicles, LTE base stations, and satellites, to name just a few applications with rigorous operating conditions.

The combination of MPS (Monolithic Power Systems) controllers with ultra-efficient eGaN^® FETs from EPC (Efficient Power Conversion) enable best-in-class power density of 1700 W/in³ in high efficiency, low cost LLC DC-DC Conversion

Standard qualification testing for semiconductors typically involves stressing devices at-or-near the limits specified in their data sheets for a prolonged period of time, or for a certain number of cycles. The goal of qualification testing is to have zero failures out of a large group of parts tested. By testing parts to the point of failure, an understanding of the amount of margin between the data sheet limits can be developed, but more importantly, an understanding of the intrinsic failure mechanisms of the semiconductor can be found.

IEEE Power Electronics Magazine
December, 2020
Read article

An automotive application using GaN power devices in high volume is lidar(light detection and ranging) for autonomous vehicles. Lidar technology provides information about a vehicle’s surroundings, thus requiring high accuracy and reliability to ensure safety and performance. This article will discus a novel testing mechanism developed by EPC to test eGaN devices beyond the qualification requirements of the Automotive Electronics Council (AEC) for the specific use case of lidar.

Power Systems Design
December, 2020
Read article

EPC introduces the 40 V, 3 milliohm EPC2055 eGaN^® FET, offering designers a device that is smaller, more efficient, and more reliable than currently available devices for high performance, space-constrained applications.

EL SEGUNDO, Calif. — December 2020 — Efficient Power Conversion Corporation, the world’s leader in enhancement-mode gallium nitride on silicon (eGaN) power FETs and ICs, advances the performance capability of low voltage, off-the-shelf gallium nitride transistors with the introduction of the EPC2055 (3 mΩ, 40 V) eGaN FET. 

EL SEGUNDO, Calif. — December 2020 — BrightLoop Converters has greatly reduced the size, cost and improved reliability of its latest BB SP DC-DC buck converters thanks to Efficient Power Conversion Corporation’s (EPC) EPC2029 enhancement-mode gallium nitride (eGaN^®) FET transistors. By switching from silicon (Si) transistors to gallium nitride (GaN), BrightLoop was able to increase the switching frequency of their design from 200 kHz to 600 kHz, while keeping the same efficiency. This design change increased the power density of the solution by a factor of approximately two and this resulted in lower cost by enabling the implementation of a smaller enclosure.

EPC’s EPC2029 is an 80 V, 48 A eGaN^® FET featuring a 1 mm ball pitch. The wider pitch allows for placement of additional and larger vias under the device to enable high current carrying capability despite the extremely small 2.6 mm x 4.6 mm footprint.

The EPC2152 ePower™ Stage enables higher performance and smaller solution size for high power density, low-cost DC-DC conversion demonstrated in the EPC9151 power module.

EL SEGUNDO, Calif.— December, 2020 — EPC announces the availability of the EPC9151, a 300 W bidirectional DC-DC voltage regulator in the in the very small 16^th brick format which is just 33 mm x 22.9 mm (1.3 x 0.9 in). The EPC9151 power module features Microchip’s dsPIC33CK digital signal controller (DSC) with the EPC2152 ePower™ Stage integrated circuit from EPC to achieve greater than 95% efficiency in a 300 W 48 V to/from 12 V converter design.  Additional phases can be added to this scalable 2-phase design to further increase power.

Gallium nitride power device technology enables a new generation of power converters in space operating at higher frequencies, higher efficiencies, and greater power densities than everachievable before. GaN power devices can also exhibit superior radiation tolerance compared with Silicon MOSFETs depending upon their device design.

Power Electronics Europe
December, 2020
Read article

Wide bandgap (WBG) semiconductors such as silicon carbide (SiC) and gallium nitride (GaN) are the new frontline in power conversion, and that takes design engineers into a whole new frequency spectrum, as well as power density and form factor opportunities.

EDN Editorial Advisory Board
December, 2020
Listen to Interview

EPC introduces 170 V, 6.8 milliohm EPC2059 eGaN^® FET, offering designers a device that is smaller, more efficient, more reliable, and lower cost than currently available devices for high performance 48 V synchronous rectification.

EL SEGUNDO, Calif. — November 2019 — Efficient Power Conversion Corporation, the world’s leader in enhancement-mode gallium nitride on silicon (eGaN) power FETs and ICs, advances the performance capability while lowering the cost of off-the-shelf gallium nitride transistors with the introduction of the EPC2059 (6.8 mΩ, 170 V) eGaN FET.  This device is the latest in a family of 100 V – 200 V solutions suitable for a wide-range of power levels and price points. They are designed to meet the increasing demands of 48 V – 56 V server and data center products as well as an array of consumer power supply applications for high end computing, including gaming PCs, LCD/LED TVs, and LED lighting.

Stefan Werkstetter appointed as New Director of Sales for EMEA to focus on assisting customers in the adoption of eGaN^® FETs and Integrated Circuits for applications including DC-DC, lidar, motor control, and other leading-edge power conversion systems

EL SEGUNDO, Calif. — November 2020 — To support the continued adoption of gallium nitride (GaN) FETs and Integrated Circuits in the European market, Efficient Power Conversion Corporation (EPC) is pleased to announce the appointment of Stefan Werkstetter as Director, Sales EMEA.

GaN technology has seen significant improvements and has reached an optimal cost for MOSFET replacement. Starting in 2017, the adoption rate of GaN in 48-Vin DC-DC converters began to take on important connotations in the market. Various topologies, such as multi-phase and multi-level bucks are offering new solutions with greater efficiency to cover the energy demands of the IT and automotive markets.

Power Electronics News
November, 2020
Read article

Gallium nitride FETs have continued to gain traction in many power electronic applications, but GaN technology is still in the early part of its life cycle. While there is much room to improve basic FET performance figures of merit an even more promising avenue is the development of GaN power ICs.

Bodo’s Power Systems
November, 2020
Read article

The ultimate aim of Artificial Intelligence is to provide machines the ability to operate autonomously. One such area which is projected to grow exponentially over the next decade is Autonomous Vehicles. With Artificial Intelligence coupled with the rapid advances in electronics and computer technology, the word driverless will soon take over the roads.

AI Time Journal
October, 2020
Read article

THIEF RIVER FALLS, Minnesota, USA – Digi-Key Electronics, the leading global electronic components distributor, announced that it has partnered with Efficient Power Conversion Corporation (EPC) to host a webinar on how to harness the power of eGaN FETS and ICs for motor drives. The webinar will take place on October 28 at 8 a.m. PST.

Register for the Harness the Power of GaN for Smaller, Lighter, More Precise Motor Drives webinar at EPC’s webinar page

Two solutions for high power density DC-DC conversion using ultra-efficient eGaN^® FETs from EPC (Efficient Power Conversion) enable highly efficient solutions for ultra-thin laptops, displays, high-end gaming systems and other physically thin consumer electronics.

EL SEGUNDO, Calif.— October, 2020 — EPC announces the availability of the EPC9148 and EPC9153 demonstration boards for 48 V DC-DC conversion.  The EPC9153 is a 250 W, extremely thin, power module using a simple, low-cost synchronous buck configuration delivering a 98.2% peak efficiency with a maximum component height of 6.5 mm.  The EPC9148 utilizes a multilevel topology enabling a maximum component height less than 4 mm, while maintaining a 98% peak efficiency.